How a competent person reduces liability through LOLER inspections

Although the Lifting Operations and Equipment Regulations 1998 (LOLER) form part of UK law and are enforced by the Health and Safety Executive (HSE), Australian employers encounter them through businesses, sites or assets connected with the United Kingdom. Australian lifting work is governed instead by the applicable state or territory work health and safety laws, plant regulations and technical standards. The familiar UK requirement for a competent person still offers a useful benchmark for anyone managing cranes, hoists, elevating work platforms or lifting accessories.

A competent person is not merely someone nominated on a form. They have the qualifications, training, practical experience and equipment-specific knowledge needed to identify hazards, assess condition, perform the required inspection or thorough examination, and issue an accurate report. Used properly, that capability reduces legal exposure by showing that lifting equipment was checked by someone capable of detecting defects and acting on them.

What competent inspection actually proves

Competence turns an inspection into reliable evidence. A capable inspector can recognise fatigue, impact damage, corrosion, distorted components, incorrect rigging and unsafe operating practices. They also understand whether a defect affects immediate safety or the safe operating limit. A tick box may satisfy administration while failing to expose the hazard that causes an injury.

Competence must match the task and equipment. A person qualified for a simple workplace lift may not be competent to undertake a statutory thorough examination of a passenger lift, crane or mobile elevating work platform. The exact legal tests and arrangements differ across Australian states and territories, while LOLER sets a UK benchmark based on qualifications, training, experience and knowledge. Employers should verify the match rather than assume one broad certification covers everything.

It is also important to distinguish a visual check from a thorough examination and test. A pre-use check can identify obvious problems; it does not necessarily uncover hidden structural weakness or verify the safety-critical functions of lifting equipment. Under LOLER, lifting equipment used to lift people is generally thoroughly examined every six months and other lifting equipment every twelve months, with further tests after substantial change. Where the law requires more than an inspection, appointing a competent person to carry out the full test and produce a suitable report prevents a false sense of compliance.

How competence reduces legal exposure

Liability rarely turns on a single signature. It develops when a duty holder failed to arrange suitable inspection, ignored information about defects, allowed defective equipment to remain in service or could not show what was done. A competent-person regime strengthens each legal duty: appropriate appointment, competent execution, prompt escalation, repair decisions and documented closure. That evidence supports a position of reasonable care while exposing any weak control that still needs attention.

Early reporting is a major liability reducer. An inspector who identifies a defect and ensures it is isolated, tagged, repaired or withdrawn from service creates a clear chain of events. If the defect caused harm, the record demonstrates how the organisation responded once it knew about the problem. Concealing, deferring or informally overriding a defect is far more damaging than a properly managed stop and repair.

Outsourcing the examination does not outsource accountability. The duty holder remains responsible for selecting the competent person, providing access and records, and ensuring recommendations are implemented. A third party supplies specialist capability; management still owns the decision to return equipment to service. Clear contracts, reporting lines and authority to stop work make that division understandable to employees, regulators, insurers and courts.

Translating LOLER controls for Australian operations

Safe Work Australia produces model work health and safety laws, but each state and territory enforces its own version through bodies such as SafeWork NSW, WorkSafe Queensland or SafeWork SA. These laws place duties on designers, suppliers, employers, workers and people who manage plant. A documented inspection and maintenance system should use the wording and requirements of the jurisdiction where the equipment is used, not a generic Australian or UK checklist.

State codes of practice and standards such as the AS 2550 crane series help translate those duties into safe-use, maintenance and operational controls. They can guide the competence standard for work platforms, forklifts, cranes, hoists and associated lifting gear. For equipment imported from the UK, retain its LOLER history where useful, but assess it against Australian requirements, loading conditions, work patterns and manufacturer instructions before service begins.

Local operating conditions make that translation essential. Mining, ports and renewables around Port Hedland, Gladstone, Newcastle and the Pilbara rely heavily on cranes, telehandlers and elevated work, often with FIFO crews, long travel routes and equipment operating thousands of kilometres. An inspection arranged around a depot calendar may fail when a machine works a twelve-hour swing in heat, dust, salt or remote isolation conditions.

Australian crews are direct about this: there are no shortcuts when a lift can drop a load or a person. The fair dinkum test is whether the nominated competent person has time, access, equipment and authority to test the actual machine in its real work environment. Local shorthand such as checking the job is “good to go” should never substitute for recorded evidence that the required inspection actually happened.

Selecting and developing a capable competent person

Selection should begin with the equipment and risk, not the cheapest quote. Ask what qualification, training, practical experience, product knowledge and test resources the person needs for that equipment and workplace. Evidence should cover a relevant trade or technical background, practical assessment for the equipment, recent experience with the same machine or system, and current knowledge of defects, safe operating limits and test methods. For complex plant, confirm whether a specialist qualification or scheme approved for that equipment is required. Check insurance, conflicts of interest and availability, because competence cannot be created by adding a title to an internal employee’s name.

A formal approval process helps prevent inconsistent appointments. Record the equipment covered, the authority granted, any limits and the review date. Reassess the appointment after major incidents, model changes or prolonged absence so the register reflects current capability.

Development should be continuous rather than a one-day certificate. A practical refresher can expose knowledge gaps, while supervised field assessments verify judgement under real conditions. The inspector also needs current manufacturer information, access to inspection procedures and an understanding of how the asset is actually used. Changes in model, lifting method, software, rigging or operating environment can make previous experience less relevant.

Building a defensible records and defect process

The inspection report is only the start of the evidence chain. It should identify the asset, its serial number, location, service, examination scope, defects, test results, limitations and the inspector’s recommendation. Calibrated test equipment strengthens that record: a suitable machine calibration overview explains how instrument accuracy and calibration traceability affect confidence in measurements. A device giving doubtful results cannot support a safe clearance, even when the inspector is highly experienced.

A robust thorough examination record normally includes:

  • Equipment identification, usage and examination date
  • Scope, method, measured results and acceptance criteria
  • Each defect, its severity and the immediate control applied
  • Inspector identity, competence basis, date and signature

Retention periods and access arrangements should match the governing law and the organisation’s risk. In a dispute, a dated original report, defect notification, work order, engineering approval and proof of testing are more useful than a vague email saying the crane is fixed. Keep superseded reports too, because the sequence of events can matter as much as the final green status.

The handover and close-out pack should show:

  • Isolation, tag-out and notification details
  • Repair, replacement or return-to-service authorisation
  • New photographs, test results and certificate or report references

For sites with multiple contractors, define who receives reports, who authorises return to service and how urgent defects are escalated outside business hours. A single defect register linked to work orders reduces contradictory records. It also lets managers see recurring problems, such as damaged wire ropes or overloaded charts, before they become systemic failures. The goal is a transparent safety decision, not a tidier folder.

Practical training that reflects real plant risks

Training works better when it resembles the work rather than a slide deck. HCF CATCH in the Humber region provides hands-on courses, apprenticeships and safety qualifications covering process, energy, engineering, electrical, health and safety, industrial gas, and wind and renewable energy in a realistic live-process-plant environment. Learners can rehearse isolation, permit-to-work, defect recognition, lifting decisions and emergency response with plant behaviour that a classroom cannot reproduce.

That realism matters for inspector development because competency combines knowledge with performance. Assessors can observe how a candidate selects a control, checks a test instrument, communicates a defect and refuses an unsafe return-to-service request. Before enrolling, read HCF CATCH reviews to understand other participants’ experience, then ask the provider for assessor credentials, equipment coverage, assessment methods and evidence of continuing industry input. Reviews inform a decision; they do not replace due diligence.

HCF CATCH also provides facility tours and room hire for conferences, meetings and training events, giving employers a way to evaluate the learning environment before committing to a course.

Australian employers can use site-based assessment and supplier demonstrations to close gaps in their own learning system. The same principle applies across the local training market, where TAFE providers, registered training organisations and specialist assessors support different parts of workforce development. Choose pathways that combine formal learning with supervised workplace practice, particularly for high-risk lifts and emerging technology such as battery or hybrid lifting equipment.

Make competence a daily control, not paperwork

The strongest LOLER inspection arrangement is built into how the organisation works. Supervisors know who is authorised to inspect which assets, competent people have the time and tools to perform their duties, and defects trigger controlled action. Managers review trends, verify that only authorised people sign off repairs and confirm that contractors meet the same standard. Competence becomes a dependable control rather than a document that exists only for an audit.

Start now by mapping every lifting asset and its inspection route, then compare that map with current LOLER or Australian legal duties and manufacturer requirements. Address competency gaps with practical training, test whether the defect process works after hours, and make sure return-to-service decisions are traceable. Arrange a facility tour or discuss a tailored training plan with HCF CATCH, and begin the competence, supervision and record-keeping improvements that protect your people, your equipment and your business.